BL2.ru

Plane truss calculator: member forces by the method of joints and the Ritter section

Enter the joints of the truss, the members (numbers of their ends), the supports and the loads at the joints. The calculator finds the reactions, solves every member force by the method of joints in an order suitable for hand work, and checks a chosen section with the Ritter method. Tension members are blue, compression members red, zero members dashed.

Joints (number = row number)
№x, my, m
1
2
3
4
5
6
You can paste a block from Excel or Word: click a cell and press Ctrl+V.
Members (numbers of the end joints)
№joint fromjoint to
1
2
3
4
5
6
7
8
9
You can paste a block from Excel or Word: click a cell and press Ctrl+V.
Supports
№JointTypeAngle, °
1
2
You can paste a block from Excel or Word: click a cell and press Ctrl+V.
Loads at the joints
№JointFxFy
1
2
3
You can paste a block from Excel or Word: click a cell and press Ctrl+V.
Supports: p is a pin (two reactions), r is a roller (one reaction, its direction is the angle from the x axis, 90 degrees by default for a vertical one). Loads are given by the components Fx and Fy: up and to the right are positive. Ritter section: the numbers of the three cut members separated by commas. Tension is positive.
Calculate

How a plane truss is analysed

A truss consists of straight members joined by pins at the joints. Loads act only at the joints, so every member works in tension or compression and carries no bending. The force N in a member is positive in tension: the member pulls the joint towards itself.

Statical determinacy

With m members, r support reactions and n joints a simple rigid truss obeys m + r = 2n. Every joint gives two equilibrium equations, the unknowns are the member forces and the reactions. If m + r < 2n the truss is a mechanism, if m + r > 2n it is statically indeterminate. A simple triangulated truss has m = 2n − 3 members with three reactions.

Method of joints

First the reactions are found from the equilibrium of the whole truss. Then a joint with no more than two unknown member forces is selected and ΣX = 0, ΣY = 0 are written. The forces found are carried to the neighbouring joints until all members are known. If two non-collinear members meet at an unloaded joint, both are zero-force members.

Method of sections (Ritter)

The truss is cut into two parts through three members. For one part the moment equation about the point where two of the cut members meet contains only the wanted force. If these two members are parallel, a projection on their normal is used instead. The method is convenient when you need the force in one member in the middle of a long truss: no need to go joint by joint.

Using the calculator

The example is a three-panel Warren truss of 12 m span with two forces on the lower chord and a section through members 4, 8 and 2. The page shows the table of forces, a coloured drawing and every step, so the solution can be copied into a coursework. The result is checked by the residual of the joint equations and by comparing both methods.

FAQ

How can I tell whether a member is in tension or compression?
By the sign of N: plus is tension, minus is compression. The force is assumed to point away from the joint; if the solution is negative the member is in compression and pushes on the joint.
What if the truss is statically indeterminate?
The condition m + r = 2n does not hold. Additional information about deformations is needed: the force or displacement method. The calculator reports the indeterminacy instead of inventing an answer.
Which members are called zero-force members?
Members with zero force under the given load. A typical sign: an unloaded joint with two non-collinear members, both are zero. Such a member keeps the truss stable and may carry force under another load.
When is the Ritter method easier than the method of joints?
When the force of one or two members in the middle of a truss is needed. Three equations of the cut part give three forces at once, with no walk through the joints, and the moment point is chosen so that only one unknown remains.
Can a roller support be inclined?
Yes. For a roller give the angle of the reaction direction from the x axis: 90 degrees is vertical, 0 is horizontal. The reaction of a roller is perpendicular to the surface it rolls on.